- Service
- Alarm system installation
- Area
- Mott Haven, Bronx, NY
- Zip code
- 10454
- Common buildings
- Apartments, co-ops and condos; Lofts and converted buildings; Two-family and multi-family houses
- Phone
- 347-258-9165
Revolvis installs alarm systems in Mott Haven (10454) for homes and businesses. New high-rise rentals, renovated tenements and industrial-to-residential conversions. A typical system here is planned around the apartment, co-op or condo: contact on the unit door, contacts on fire-escape and reachable windows and phone alerts. Our licensed in-house crew designs it on a free site visit.
The buildings we alarm in Mott Haven
Mott Haven is the South Bronx's waterfront gateway, with new residential towers rising beside industrial blocks and older tenement streets.
- New high-rise rentals, renovated tenements and industrial-to-residential conversions.
- Many buildings are multi-family with shared entries.
- Brick and concrete construction dominates.
- The Hub at 149th Street is the commercial center.
- Industrial blocks and waterfront developments mix in.
What an alarm needs here
Based on those buildings, these are the setups we plan most often in Mott Haven.
Apartments, co-ops and condos
In an apartment the unit door is the main risk, followed by any window on a fire escape or within reach of a roof or setback. Wireless sensors avoid drilling through plaster and keep a board or landlord comfortable. A keypad by the door and an interior siren are usually enough, and the system can move with you.
- Contact on the unit door
- Contacts on fire-escape and reachable windows
- One motion sensor covering the entry hall
- Keypad at the door and an interior siren
Lofts and converted buildings
Lofts are large open rooms with oversized windows, so the plan changes. A few long-range motion sensors replace the many small ones a divided home needs, and glass-break sensors cover the window walls. Freight doors, roof hatches and shared corridors each get their own contact.
- Long-range motion sensors for open floors
- Glass-break sensors for window walls
- Contacts on freight, corridor and roof doors
- Asset protection for equipment or artwork
Two-family and multi-family houses
When two or more households share a building, each unit needs to arm and disarm on its own. The system is split into partitions, one per apartment, with the shared basement, side door and hallway on a common zone the owner controls. Tenants never need each other’s codes.
- Separate partition and keypad for each unit
- Contacts on the shared front and side doors
- Contact and motion sensor for the shared basement
- Contact on any roof or bulkhead door
Near the water
Salt air and damp shorten the life of cheap outdoor hardware, so exterior sounders and contacts are sealed, corrosion-resistant models. Basements near the water also benefit from flood sensors on the same panel, which alert you to water before it becomes damage.
- Corrosion-resistant exterior devices
- Water sensors in the basement or utility room
Warehouses and industrial buildings
Large buildings need sensors made for them: contacts on dock and overhead doors, long-range or beam detection across open floors and aisles, and sounders loud enough to carry. Zones are split by area so one open dock door does not disarm the whole site.
- Contacts on dock and overhead doors
- Long-range or beam motion detection
- High-output sounders
- Zones split by area of the building
A typical Mott Haven alarm plan
Combining the building types above, a full system here usually includes:
- Contact on the unit door
- Contacts on fire-escape and reachable windows
- One motion sensor covering the entry hall
- Keypad at the door and an interior siren
- Long-range motion sensors for open floors
- Glass-break sensors for window walls
- Contacts on freight, corridor and roof doors
- Asset protection for equipment or artwork
- Separate partition and keypad for each unit
- Contacts on the shared front and side doors
- Control panel with battery backup, keypad, siren and phone app
Build a sensor checklist
Pre-set for the most common building type in Mott Haven. Adjust it to match your property.
What owners in Mott Haven ask us for
- New developments and building entries lead the asks.
- Owners want lobby coverage and access control.
- New developments need lobby, package-room and entry control.
- Mixed residential-industrial blocks need perimeter coverage.
Every system starts with a free site visit in Mott Haven and a custom quote. How alarm installation works →
Alarm systems in Mott Haven: common questions
Who installs alarm systems in Mott Haven?
Revolvis installs alarm systems in Mott Haven, Bronx, NY 10454 with its own licensed in-house crew. We visit the property for free, design the system for the building and give a custom quote.
Can I install an alarm in a co-op or rental apartment?
Yes. Wireless sensors need no cabling through walls. Check your building rules or lease first, and we can provide the equipment details a board or landlord asks for.
How do you alarm a large open loft?
With long-range motion sensors and glass-break detection for the window walls, plus contacts on freight and roof doors, instead of a sensor in every room.
Can each apartment have its own alarm code?
Yes. The system is divided into partitions so every unit arms and disarms separately, while the owner keeps control of shared doors and the basement.
How much does an alarm system cost in Mott Haven?
It depends on the number of doors and windows covered and whether sensors are wired or wireless. We quote after a free site visit, with no obligation.
Can I arm and disarm from my phone?
Yes. The app lets you arm, disarm and see which sensor triggered, from anywhere.
Can the alarm work with security cameras?
Yes. An alarm event can trigger recording and send a video clip to your phone, so you see what set it off.
